A Uniform Viscoelastic-Plastic Constitutive Model for MD-PMMA at a Wide Temperature Range

Authors

  • Wei Liu School of Mechanics, Civil Engineering & Architecture, Northwestern Polytechnical University, Xi’an 710129, China
  • Wei-Hao Zhai School of Mechanics, Civil Engineering & Architecture, Northwestern Polytechnical University, Xi’an 710129, China

DOI:

https://doi.org/10.6000/1929-5995.2015.04.03.2

Keywords:

Constitutive model, plastic strain, temperature, MD PMMA, internal stress

Abstract

The deformation characteristics of MD-PMMA vary greatly at different temperatures. In the paper, whether a uniform model could be used to describe these complex characteristics was discussed. Tensile properties of MD-PMMA at the temperatures of -50˚C, -25˚C, 20˚C, 60˚C, 90˚C were experimentally investigated. The entire deformation processes of PMMA were divided into four stages: elastic stage, viscoelastic stage, yielding stage and post-yielding stage. Strain softening and strain hardening phenomenon occurred in the yielding and post-yielding stage, it was the results of the competition between loading rate and plastic strain rate. A nonlinear model of activation dashpot was constructed, in the model, the evolution rate of plastic deformation was defined by Eyring’s theory, and the actual stress was the difference between external applied stress and internal resistance stress caused by plastic strain. The above activation dashpot serially connected with the standard linear model (SLM) to identify elastic and viscoelastic characteristics. A two iterations integral algorithm was proposed to simplify the inter-coupling between the internal stress and the plastic strain, and the unknown parameters in the model could be easily fitted by the experimental data. This uniform viscoelastic-plastic model was demonstrated that could predict different deformation behaviors at a wide temperature range.

References

Wu HY, Ma G, Xia YM. Experimental study of tensile properties of PMMA at intermediate strain rate. Mater Lett 2004; 58: 3681-5. http://dx.doi.org/10.1016/j.matlet.2004.07.022 DOI: https://doi.org/10.1016/j.matlet.2004.07.022

Guo WG, Shi FF. Deformation and failure behavior of MDYB-3 oriented PMMA glass under different loading conditions. Acta Aeronautica Et Astronautica Siniga 2008; 29: 1517-25.

Zhang CT, Moore ID. Nonlinear mechanical response of high density polyethylene. Part II: Uniaxial constitutive modeling. Poly Eng & Sci 1997; 37: 414-20. http://dx.doi.org/10.1002/pen.11684 DOI: https://doi.org/10.1002/pen.11684

Zhang Y, Huang ZP. A model for the nonlinear viscoelastic behavior of amorphous polymers. Mech Res Commun 2004; 31: 195-202. http://dx.doi.org/10.1016/j.mechrescom.2003.09.002 DOI: https://doi.org/10.1016/j.mechrescom.2003.09.002

Segreti M, Rusinek A, Klepaczko JR. Experimental study on puncture of PMMA at low and high velocities, effect on the failure mode. Polym Test 2004; 23: 703-18. http://dx.doi.org/10.1016/j.polymertesting.2004.01.005 DOI: https://doi.org/10.1016/j.polymertesting.2004.01.005

Forquin P, Nasraoui M, Rusinek A, et al. Experimental study of the confined behaviour of PMMA under quasi-static and dynamic loadings. Int J Impact Eng 2012; 40: 46-57. http://dx.doi.org/10.1016/j.ijimpeng.2011.09.007 DOI: https://doi.org/10.1016/j.ijimpeng.2011.09.007

Xie ZQ, Zhang PP. On the Dynamic compressive mechanical properties and strain rate related constitutive model of PMMA material. J Exp Mech 2013; 28: 220-6.

Varghese AG, Batra RC. Constitutive equations for the thermomechanical deformations of glassy polymers. Int J Solids Struct 2009; 46: 4079-94. http://dx.doi.org/10.1016/j.ijsolstr.2009.08.006 DOI: https://doi.org/10.1016/j.ijsolstr.2009.08.006

Fleischhauer R, Dal H, Kaliske M, et al. A constitutive model for finite deformation of amorphous polymers. Int J Mech Sci 2012; 65: 48-63. http://dx.doi.org/10.1016/j.ijmecsci.2012.09.003 DOI: https://doi.org/10.1016/j.ijmecsci.2012.09.003

Chaboche JL. A review of some plasticity and viscoplasticity constitutive theories. Int J Plasticity 2008; 24: 1642-93. DOI: https://doi.org/10.1016/j.ijplas.2008.03.009

Eyring H. Viscosity, plasticity, and diffusion as examples of absolute reaction rates. J Chem Phys 1936; 4: 283-91. http://dx.doi.org/10.1063/1.1749836 DOI: https://doi.org/10.1063/1.1749836

Zhu XX. Yielding and plastic deformation of solid polymers. Adv Mech 1992; 22: 449-63.

Ayoub G, Zairi F, Abdelaziz MN, et al. Modeling large deformation behavior under loading-unloading of semicrystalline polymers: Application to a high density polyethylene. Int J Plasticity 2010; 26: 329-47. http://dx.doi.org/10.1016/j.ijplas.2009.07.005 DOI: https://doi.org/10.1016/j.ijplas.2009.07.005

Argon AS. A theory for the low temperature plastic deformation of glassy polymers. Philos Mag 1973; 28: 839-65. http://dx.doi.org/10.1080/14786437308220987 DOI: https://doi.org/10.1080/14786437308220987

Ozgen UC. Modeling deformation behavior of polymers with viscoplasticity theory based on overstress. Int J Plasticity 2005; 21: 145-60. http://dx.doi.org/10.1016/j.ijplas.2004.04.004 DOI: https://doi.org/10.1016/j.ijplas.2004.04.004

Boyce M, Parks D, Argon AS. Large inelastic deformation of glassy polymers. Part I: rate dependent constitutive model. Mech Mater 1988; 7: 15-33. http://dx.doi.org/10.1016/0167-6636(88)90003-8 DOI: https://doi.org/10.1016/0167-6636(88)90003-8

Anand L, Gurtin ME. A theory of amorphous solids undergoing large deformations, with application to polymeric glasses. Int J Solids Struct 2003; 40: 1465-87. http://dx.doi.org/10.1016/S0020-7683(02)00651-0 DOI: https://doi.org/10.1016/S0020-7683(02)00651-0

Haward RN, Thackray G. The use of a mathematical model to describe isothermal stress-strain curves in glassy thermoplastics. Proc Royal Soc Lond Ser A Math Phys Sci 1968; 302: 453-72. DOI: https://doi.org/10.1098/rspa.1968.0029

Richeton J, Ahzi S, Vecchio KS, et al. Influence of temperature and strain rate on the mechanical behavior of three amorphous polymers: Characterization and modeling of the compressive yielding stress. Int J Solids Struct 2006; 43: 2318-35. http://dx.doi.org/10.1016/j.ijsolstr.2005.06.040 DOI: https://doi.org/10.1016/j.ijsolstr.2005.06.040

Wu PD, Giessen VD. On improved network models for rubber elasticity and their applications to orientation hardening in glassy polymers. J Mech Phys Solids 1993; 41: 427-56. http://dx.doi.org/10.1016/0022-5096(93)90043-F DOI: https://doi.org/10.1016/0022-5096(93)90043-F

Arruda EM, Boyce MC, Jayachandran R. Effects of strain rate, temperature and theromechanical coupling on the finite strain deformation of glassy polymers, Mech Mater 1995; 19: 193-212. http://dx.doi.org/10.1016/0167-6636(94)00034-E DOI: https://doi.org/10.1016/0167-6636(94)00034-E

Dupaix RB, Boyce MC. Constitutive modeling of the finite strain behavior of amorphous polymers in and above the glass transition. Mech Mater 2007; 39: 39-52. http://dx.doi.org/10.1016/j.mechmat.2006.02.006 DOI: https://doi.org/10.1016/j.mechmat.2006.02.006

AnandL, Ames NM, Srivastava V, et al. A thermo-mechanically coupled theory for large deformations of amorphous polymers. Part I: Formulation. Int J Plasticity 2009; 25: 1474-94. http://dx.doi.org/10.1016/j.ijplas.2008.11.004 DOI: https://doi.org/10.1016/j.ijplas.2008.11.004

Miehe C, Diez JM, Goktepe S, et al. Coupled thermoviscoplasticity of glassy polymers in the logarithmic strain space based on the free volume theory. Int J Solids Struct 2011; 48: 1799-817. http://dx.doi.org/10.1016/j.ijsolstr.2011.01.030 DOI: https://doi.org/10.1016/j.ijsolstr.2011.01.030

Zhu XX, Zhu GR, Huang XS, et al. The nonlinear thermoviscoelastic plastic constitutive relations for an

aeronautical PMMA. Acta Aeronautica Et Astronautica Sinica 1992; 13: 594-601.

Ward IM. The mechanical properties of solid polymers. Beijing: Science Press1988.

Gao ZZ, Liu W, Liu ZQ, et al. Experiment and simulation study on the creep behavior of PMMA at different temperatures. Polym Plast Technol 2010; 49: 1478-82. http://dx.doi.org/10.1080/03602559.2010.496429 DOI: https://doi.org/10.1080/03602559.2010.496429

Downloads

Published

2015-10-28

How to Cite

Liu, W., & Zhai, W.-H. (2015). A Uniform Viscoelastic-Plastic Constitutive Model for MD-PMMA at a Wide Temperature Range. Journal of Research Updates in Polymer Science, 4(3), 139–148. https://doi.org/10.6000/1929-5995.2015.04.03.2

Issue

Section

Articles